Publication detail

Combined jet and exhaust flow interacting with an obstacle

KREJČÍ, V. KOŠNER, J.

Czech title

Kombinace proudu a odsávání v interakci s překážkou

English title

Combined jet and exhaust flow interacting with an obstacle

Type

conference paper

Language

en

Original abstract

The article deals with a combined jet and exhaust flow as generated by an Aaberg exhaust hood and its interaction with the obstacle. The obstacle was a disc aligned with the jet flow and located coaxially to the jet. The diameter of the disc was 550 mm. The air terminal dimensions were: supply slot diameter 200 mm and supply slot width 4 mm. Two operation modes were tested. First, jet only flow at 10 m/s of the exit jet velocity. Second, combined flow mode at which the exhaust velocity was set to 9.13 m/s, keeping the jet exit velocity fixed. The hood operational parameter I was thus 0.6. The obstacle surface roughness was varied by means of sand paper to map the hysteretic jet behaviour when moving the obstacle towards or away from the air terminal.

Czech abstract

Článek se zabývá složeným přívodním a odsávacím prouděním generovaným pomocí Aabergova nástavce a jeho interakcí s překážkou. Překážku představoval kotouč umístěný souose s nástavcem a tak, že osa proudu byla rovnoběžná s povrchem kotouče. Průměr kotouče byl 550 mm. Rozměry nástavce byly následující: průměr přívodní příruby 200 mm, šířka přívodní štěrbiny 4 mm. Byly testovány dva provozní režimy, a to: jen radiální proud o střední počáteční rychlosti 10 m/s a kombinované proudění s odsávací rychlostí 9,13 m/s (rychlost radiálního proudu byla zachována. Poměr hybnostních toků I byl tedy roven 0.6. Drsnost povrchu kotouče byla měněna pomocí smirkového papíru. Pohybem kotouče směrem k nebo od nástavce bylo zmapováno hysterezní chování radiálního proudu.

English abstract

The article deals with a combined jet and exhaust flow as generated by an Aaberg exhaust hood and its interaction with the obstacle. The obstacle was a disc aligned with the jet flow and located coaxially to the jet. The diameter of the disc was 550 mm. The air terminal dimensions were: supply slot diameter 200 mm and supply slot width 4 mm. Two operation modes were tested. First, jet only flow at 10 m/s of the exit jet velocity. Second, combined flow mode at which the exhaust velocity was set to 9.13 m/s, keeping the jet exit velocity fixed. The hood operational parameter I was thus 0.6. The obstacle surface roughness was varied by means of sand paper to map the hysteretic jet behaviour when moving the obstacle towards or away from the air terminal.

Keywords in Czech

Aabergův nástavec, interakce radiálního proudu se stěnou, drsnost povrchu

Keywords in English

Aaberg hood, radial jet – wall interaction, hysteresis, wall roughness

RIV year

2010

Released

24.11.2010

Publisher

Technical University of Liberec

Location

Liberec

ISBN

978-80-7372-670-6

Book

Proceedings of the international conference Experimental Fluid Dynamics 2010

Edition number

1

Pages from–to

301–309

Pages count

8

BIBTEX


@inproceedings{BUT35103,
  author="Vladimír {Krejčí} and Jan {Košner},
  title="Combined jet and exhaust flow interacting with an obstacle",
  booktitle="Proceedings of the international conference Experimental Fluid Dynamics 2010",
  year="2010",
  month="November",
  pages="301--309",
  publisher="Technical University of Liberec",
  address="Liberec",
  isbn="978-80-7372-670-6"
}