Publication detail
Effect of wirefeed rate on the morphology of a surface machined using WEDM
MOURALOVÁ, K. KOVÁŘ, J. BENEŠ, L. OSIČKA, K.
Czech title
VLIV RYCHLOSTI ODVÍJENÍ DRÁTU NA MORFOLOGII POVRCHU OBROBENÉM WEDM
English title
Effect of wirefeed rate on the morphology of a surface machined using WEDM
Type
journal article in Scopus
Language
en
Original abstract
Wire electrical discharge machining (WEDM) is an unconventional technology of machining that uses physical phenomena for material cutting. During wire electrical discharge machining craters are formed on the workpiece surface, and blended and molten material of both workpiece and wire electrode get stuck here due to diffusion processes. The study deals with the assessment of the influence of wire feed rate on quantitative and qualitative evaluations of craters on the workpiece made of X155CrVMo12-1 alloy tool steel. The diffusion phenomena that had occurred on the surface during the process of cutting were studied using light microscopy. Attention was also given to the detail study of the used brass electrode where the level of wear and degradation in terms of the quality of morphology were studied after the process of cutting.
Czech abstract
Elektroerozivní drátové řezání (WEDM) je nekonvenční technologie obrábění, která využívá k dělení materiálu fyzikálních jevů. Při elektroerozivním obrábění vznikají na povrchu obrobku krátery a díky difuzním pochodům zde uplývá promísený a natavený materiál obroku i drátové elektrody. Studie se zabývá vyhodnocením vlivu rychlosti odvíjení drátové elektrody na kvantitativní i kvalitativní vyhodnocení kráterů na povrchu obrobku z nástrojové oceli X155CrVMo12-1. S využitím světelné mikroskopie byly studovány difuzní povrchové jevy vzniklé v průběhu procesu řezání. Pozornost byla věnována i detailnímu studiu použité mosazné elektrody, u které byla zjišťována míra opotřebení po řezném procesu a současně i její degradace z hlediska kvality morfologie.
English abstract
Wire electrical discharge machining (WEDM) is an unconventional technology of machining that uses physical phenomena for material cutting. During wire electrical discharge machining craters are formed on the workpiece surface, and blended and molten material of both workpiece and wire electrode get stuck here due to diffusion processes. The study deals with the assessment of the influence of wire feed rate on quantitative and qualitative evaluations of craters on the workpiece made of X155CrVMo12-1 alloy tool steel. The diffusion phenomena that had occurred on the surface during the process of cutting were studied using light microscopy. Attention was also given to the detail study of the used brass electrode where the level of wear and degradation in terms of the quality of morphology were studied after the process of cutting.
Keywords in Czech
WEDM, elektroerozivní drátové řezání, ocel X155CrVMo12-1, povrchová vrstva, rychlost odvíjení drátu
Keywords in English
WEDM, Electrical Discharge Machining, steel X155CrVMo12-1, surface layer, wire feed
Released
23.08.2016
Publisher
UJEP
Location
Ústí nad Labem
ISSN
1213-2489
Volume
2016
Number
4
Pages from–to
754–757
Pages count
4
BIBTEX
@article{BUT126624,
author="Kateřina {Mouralová} and Jiří {Kovář} and Libor {Beneš} and Karel {Osička},
title="Effect of wirefeed rate on the morphology of a surface machined using WEDM",
year="2016",
volume="2016",
number="4",
month="August",
pages="754--757",
publisher="UJEP",
address="Ústí nad Labem",
issn="1213-2489"
}