Detail publikace

VLIV RYCHLOSTI ODVÍJENÍ DRÁTU NA MORFOLOGII POVRCHU OBROBENÉM WEDM

MOURALOVÁ, K. KOVÁŘ, J. BENEŠ, L. OSIČKA, K.

Český název

VLIV RYCHLOSTI ODVÍJENÍ DRÁTU NA MORFOLOGII POVRCHU OBROBENÉM WEDM

Anglický název

Effect of wirefeed rate on the morphology of a surface machined using WEDM

Typ

článek v časopise ve Scopus, Jsc

Jazyk

en

Originální abstrakt

Wire electrical discharge machining (WEDM) is an unconventional technology of machining that uses physical phenomena for material cutting. During wire electrical discharge machining craters are formed on the workpiece surface, and blended and molten material of both workpiece and wire electrode get stuck here due to diffusion processes. The study deals with the assessment of the influence of wire feed rate on quantitative and qualitative evaluations of craters on the workpiece made of X155CrVMo12-1 alloy tool steel. The diffusion phenomena that had occurred on the surface during the process of cutting were studied using light microscopy. Attention was also given to the detail study of the used brass electrode where the level of wear and degradation in terms of the quality of morphology were studied after the process of cutting.

Český abstrakt

Elektroerozivní drátové řezání (WEDM) je nekonvenční technologie obrábění, která využívá k dělení materiálu fyzikálních jevů. Při elektroerozivním obrábění vznikají na povrchu obrobku krátery a díky difuzním pochodům zde uplývá promísený a natavený materiál obroku i drátové elektrody. Studie se zabývá vyhodnocením vlivu rychlosti odvíjení drátové elektrody na kvantitativní i kvalitativní vyhodnocení kráterů na povrchu obrobku z nástrojové oceli X155CrVMo12-1. S využitím světelné mikroskopie byly studovány difuzní povrchové jevy vzniklé v průběhu procesu řezání. Pozornost byla věnována i detailnímu studiu použité mosazné elektrody, u které byla zjišťována míra opotřebení po řezném procesu a současně i její degradace z hlediska kvality morfologie.

Anglický abstrakt

Wire electrical discharge machining (WEDM) is an unconventional technology of machining that uses physical phenomena for material cutting. During wire electrical discharge machining craters are formed on the workpiece surface, and blended and molten material of both workpiece and wire electrode get stuck here due to diffusion processes. The study deals with the assessment of the influence of wire feed rate on quantitative and qualitative evaluations of craters on the workpiece made of X155CrVMo12-1 alloy tool steel. The diffusion phenomena that had occurred on the surface during the process of cutting were studied using light microscopy. Attention was also given to the detail study of the used brass electrode where the level of wear and degradation in terms of the quality of morphology were studied after the process of cutting.

Klíčová slova česky

WEDM, elektroerozivní drátové řezání, ocel X155CrVMo12-1, povrchová vrstva, rychlost odvíjení drátu

Klíčová slova anglicky

WEDM, Electrical Discharge Machining, steel X155CrVMo12-1, surface layer, wire feed

Vydáno

23.08.2016

Nakladatel

UJEP

Místo

Ústí nad Labem

ISSN

1213-2489

Ročník

2016

Číslo

4

Strany od–do

754–757

Počet stran

4

BIBTEX


@article{BUT126624,
  author="Kateřina {Mouralová} and Jiří {Kovář} and Libor {Beneš} and Karel {Osička},
  title="Effect of wirefeed rate on the morphology of a surface machined using WEDM",
  year="2016",
  volume="2016",
  number="4",
  month="August",
  pages="754--757",
  publisher="UJEP",
  address="Ústí nad Labem",
  issn="1213-2489"
}