Publication detail
Influence of Chemical Additives and Curing Conditions on Mechanical Properties and Carbonation Resistance of Alkali Activated Slag Composites
BULEJKO, P. BÍLEK, V.
Czech title
Vliv chemických přísad a podmínek vytvrzování na mechanické vlastnosti a odolnost vůči karbonataci kompozitů na bázi alkalicky aktivované strusky
English title
Influence of Chemical Additives and Curing Conditions on Mechanical Properties and Carbonation Resistance of Alkali Activated Slag Composites
Type
abstract
Language
en
Original abstract
The main aim of the presented work is to investigate the effect of the addition of air entraining (AEA) and shrinkage reducing agents (SRA) on mechanical properties and carbonation resistance of alkali activated slag (AAS). Materials for the sample preparation were blast furnace slag activated using sodium silicate and AEA or SRA varying in content. Curing of samples was carried out in various conditions (air curing at laboratory conditions and water curing at the same temperature) and influence of these was studied too. The prepared samples (specimens with dimensions of 100 mm × 20 mm × 20 mm) where tested on compressive and bending strengths. The experimental results have shown that the addition of AEA had not significant influence on the mechanical properties while the addition of SRA had negative effect. However, the carbonation resistance markedly decreases with increasing amount of both agents. The same stands for the air curing as mechanical strengths are lower compared to those cured in water and the ratio of strength of the air cured composite and that of water cured one decreases with increasing content of SRA.
Czech abstract
Hlavním cílem předložené práce je zjištění účinku přídavku provzdušňujících (AEA) a smršťování redukčních činidel (SRA) na mechanické vlastnosti a odolnost vůči karbonataci alkalicky aktivovaného strusky (AAS). Materiály pro přípravu vzorku byly vysokopecní struska aktivovaná za použití křemičitanu sodného a AEA nebo SRA různého obsahu. Vytvrzování vzorků byla prováděna v různých podmínkách (vytvrzování v laboratorních podmínkách a ve vodě při stejné teplotě), a vliv těchto byl studován také. Připravené vzorky (vzorky o rozměrech 100 mm x 20 mm x 20 mm), byly testovány na pevnost v tlaku a v ohybu. Experimentální výsledky ukázaly, že přídavek AEA neměl významný vliv na mechanické vlastnosti, zatímco přidání SRA mělo negativní dopad. Nicméně, odolnost vůči karbonataci výrazně klesá se zvyšujícím se množstvím obou činidel. Stejné platí pro vytvrzování vzduchem, mechanické pevnosti jsou nižší v porovnání s vytvrzovanými ve vodě a poměr pevnosti na vzduchu vytvrzeného kompozitu a ve vodě vytvrzeného klesá se stoupajícím obsahem SRA.
English abstract
The main aim of the presented work is to investigate the effect of the addition of air entraining (AEA) and shrinkage reducing agents (SRA) on mechanical properties and carbonation resistance of alkali activated slag (AAS). Materials for the sample preparation were blast furnace slag activated using sodium silicate and AEA or SRA varying in content. Curing of samples was carried out in various conditions (air curing at laboratory conditions and water curing at the same temperature) and influence of these was studied too. The prepared samples (specimens with dimensions of 100 mm × 20 mm × 20 mm) where tested on compressive and bending strengths. The experimental results have shown that the addition of AEA had not significant influence on the mechanical properties while the addition of SRA had negative effect. However, the carbonation resistance markedly decreases with increasing amount of both agents. The same stands for the air curing as mechanical strengths are lower compared to those cured in water and the ratio of strength of the air cured composite and that of water cured one decreases with increasing content of SRA.
Keywords in English
Alkali-activated slag, carbonation resistance, chemical additives, mechanical properties
Released
28.09.2015
Publisher
Inštitut za kovinske materiale in tehnologije
Location
Ljubljana, Lepi pot 11, Ljubljana, Slovenija
ISBN
978-961-92518-8-1
Book
23rd INTERNATIONAL CONFERENCE ON MATERIALSAND TECHNOLOGY PROGRAM AND BOOK OF ABSTRACTS
Pages from–to
66–66
Pages count
1