Detail publikace
PROBLEMATIKA OBRÁBĚNÍ SVAŘOVACÍ ELEKTRODY Z ČISTÉHO MOLYBDÉNU POMOCÍ WEDM
MOURALOVÁ, K. ZAHRADNÍČEK, R. HRDÝ, R.
Český název
PROBLEMATIKA OBRÁBĚNÍ SVAŘOVACÍ ELEKTRODY Z ČISTÉHO MOLYBDÉNU POMOCÍ WEDM
Anglický název
Using WEDM machine a pure molybdenum welding electrode
Typ
článek v časopise ve Scopus, Jsc
Jazyk
en
Originální abstrakt
The unconventional wire electric discharge machining technology (WEDM) is widely used in many industries, which is why thereis a permanent emphasis on increasing the quality of such machined surface. The aim of this studywas to carry out a design of experiment (DoE) to reduce the surface qualityparameterPq. During the 33-round experiment, the input factors – machine setting parameters, such as gap voltage, pulse on time, pulse off time, wire speed, and dischargecurrent, werechanged. Subsequently, Pq – rootmean square deviation of the primary profile and Pa – arithmetic average of the primary profile were evaluated on the machined surfaces of pure aluminium. By using DoE, the setting of the machine’ sparameters was designed in order to achieve the highest possible surface quality.
Český abstrakt
Materiály s vysokou teplotou tání, jako je například molybden, jsou vhodné pro vysokoteplotní fyzikální aplikace ale i pro výrobu svařovacích elektrod či dráty pro elektroerozivní drátové řezačky. Pro obrábění čistého molybdenu je kromě konvenčních metod často užíváno i nekonvenční technologie elektroerozivního drátového řezání (WEDM). Cílem této studie byla detailní analýza WEDM obrobeného povrchu a jeho defektů, konkrétně pro svařovací elektrodu. Užitím kontaktního profilometru a mikroskopu atomárních sil (AFM) byly získány komplexní informace o topografii včetně 3D barevně filtrovaného reliéfu povrchu. Defekty obrobených povrchů byly studovány pomocí elektronové mikroskopie přímo na povrchu vzorku i v jeho příčném řezu. Dále byla provedena lokální analýza chemického složení a měření tvrdosti podpovrchové vrstvy.
Anglický abstrakt
The unconventional wire electric discharge machining technology (WEDM) is widely used in many industries, which is why thereis a permanent emphasis on increasing the quality of such machined surface. The aim of this studywas to carry out a design of experiment (DoE) to reduce the surface qualityparameterPq. During the 33-round experiment, the input factors – machine setting parameters, such as gap voltage, pulse on time, pulse off time, wire speed, and dischargecurrent, werechanged. Subsequently, Pq – rootmean square deviation of the primary profile and Pa – arithmetic average of the primary profile were evaluated on the machined surfaces of pure aluminium. By using DoE, the setting of the machine’ sparameters was designed in order to achieve the highest possible surface quality.
Klíčová slova česky
WEDM, elektroerozivní obrábění,čistý molybden, topografie povrchu,svařovací elektroda
Klíčová slova anglicky
WEDM, electrical discharge machining, pure molybdenum, topography of surface, electrode for welding
Vydáno
02.09.2017
Nakladatel
MM Science Journal
Místo
Praha
ISSN
1803-1269
Ročník
2017
Číslo
4
Strany od–do
2109–2113
Počet stran
5
BIBTEX
@article{BUT138911,
author="Kateřina {Mouralová} and Radim {Zahradníček} and Radim {Hrdý},
title="Using WEDM machine a pure molybdenum welding electrode",
year="2017",
volume="2017",
number="4",
month="September",
pages="2109--2113",
publisher="MM Science Journal",
address="Praha",
issn="1803-1269"
}